Air Conditioning 


Timber Dryers 


Military Equipment 



Product Data

  Part Number
Height (mm) 1,400
Width (mm) 2,000
Depth (mm) 1,000
Weight(kgs) 505
Voltage 415
Phase 3
Frequency(Hz) 50
Typical Current(A) 10
Heating Power(kW) 24
Gas Regen Option (TBC) TBC
Steam Regen Option (m3/hr) 7.0
Electric Regen Option(kW) 24
Rotor Size (dia X depth mm) 650 X 200
Process Airflow - Dry Air (m3/hr) 3,000
Process Airflow Static Pressure(pa) 1,245
Regen Airflow - Wet Air (m3/hr) 750
Regen Airflow Static Pressure(pa) 797
Process Air Duct Size (mm) 400
Process Air Inlet (L X W mm) 740 X 535
Regen Air Duct Size - Wet Air (mm) 250
Regen Air Inlet (L X W mm) 485 X 485
Typical Extraction(l/d) 438
Min Operating Temp (°C) -20
Max OperatingTemp (°C) 40
  Part Number
On/Off Control Y
Electronic Controls Y
Manual / Automatic Mode Selection Y
Remote Humidistat Sensor Facility Y
Mains Isolator Y
Variable Fan Speeds (Speed Controlled) Y
Steam Regeneration Option Y
Gas Regeneration Option Y
Electric Regeneration Option Y
Process / Regen Air Fliter Y
Dual Inlet Design Y
Free Standing Y
High Temperature Safety Cut-outs Y
Humidistat O
Stainless Steeel Construction O
Inlet Duct Attachements O
Part Number Description
3035157 Humidistat Manual
3035159 Humidistat Int Sen 230V
3035161 Humidistat Ext Sen 230V
  Part Number
Wiring Diagram
Wiring Schematic
Spare Parts List


Dehumidifiers are required wherever there is a need to lower the humidity level to prevent corrosion, mould growth and condensation or maintain a low humidity condition during manufacture, packaging or storing of hygroscopic products.


Dehumidification is possible using two possible principles, Condensation with refrigeration style dehumidifiers and Adsorption with desiccant dehumidifiers. Desiccant dehumidifiers perform exceptionally well when used in cooler climates, or when a low dew-point, deep drying or low humidity levels are required. Since desiccant dehumidifiers do not produce water, they will work effectively down to sub zero temperatures. Their operation is simplistic yet extremely effective and reliable. Air (Process Air) is drawn into the dehumidifier, where is passes over a wheel impregnated with Silica Gel. As the air passes over this wheel, any moisture present in the air, is absorbed into the Silica Gel wheel before leaving the dehumidifier as warm dry air. The Silica Gel wheel is continually, slowly rotating, typically at three revolutions per hour. As the wheel rotates a small portion passes through the regeneration segment. During this phase a second air stream (Regeneration Air) is heated to a high temperature before passing over the wheel. Any moisture present in the wheel is released into this air stream, this hot wet air is then exhausted outside the area being dried.


EIPL is Europe’s leading manufacturer of dehumidifiers and is a name you can rely on. No matter how extreme the conditions EIPL’s efficiency copes comfortably even at the coldest temperatures.


Over thirty seven years of development experience means you can rely on the proven track record of the EIP range of dehumidifiers. Every dehumidifier is designed for efficiency and ruggedness, and built to last. The popularity of EIP Ltd’s dehumidifiers with the plant hire trade speaks for their reliability, portability and outstanding durability


The EIPL desiccant dehumidifiers all incorporate the well proven, Proflute / Munters desiccant wheels thereby ensuring their products, as a minimum, equal performance to major competitors products. This range of large desiccant dehumidifiers, have been designed to accommodate a wide range of regeneration heat sources, ie electric, steam and gas, thereby ensuring a wide variety of installations are accommodated. The programmable electronic controller, and high capacity EC process fan, allows easy installation and also the flexibility for the end user to fine tune drying capacities catering for, high extraction, high efficiency or deep drying, depending upon the final application. Facility for an external humidistat allows remote control of the drying cycleAll models incorporate a high efficiency patented PPS Rotor. This design incorporates an 82% active Silica Gel to ensure optimum performance over the equipments wide operating range of environments. All desiccant rotors supplied by EIPL are washable, and designed for high performance / long life. The chassis design incorporates access points for fork lifts and pallet trucks, allowing for easy maneuvering into awkward site locations. All side panels are removable, allowing for easy servicing and maintenance. Should a fault arise various fault indicator lamps allow easy diagnostics and thereby minimum downtime.

Facility for an external humidistat allows the humidity level to be maintained at a preset condition. The EIPL range of desiccant dehumidifiers incorporate a rotors with a 82% active Silica Gel, thereby ensuring optimum performance over the equipments wide operating range